TS-850: Difference between revisions
No edit summary |
No edit summary |
||
| (6 intermediate revisions by the same user not shown) | |||
| Line 34: | Line 34: | ||
=IF OUT= | =IF OUT= | ||
[[Image:Ts850s_ifout.png|none|frame|TS-850s IF OUT konektor]] | [[Image:Ts850s_ifout.png|none|frame|TS-850s IF OUT konektor]] | ||
=CAT= | |||
[[Image:Ts850s_cat.png|none|frame|TS-850s IF OUT konektor]] | |||
=Blokový diagram= | =Blokový diagram= | ||
[[ | [[TS-850 BlockDiagram]] | ||
=Servisní menu= | |||
Pressing SCAN + TX-M.CH will set the radio into its extended function mode. These options can be scrolled via the M.CH/VFO CH. switch. The following are the extended functions: | |||
* 00 - This is the ROM Ce`ecksum displayed as a 4-digit hexadecimal number. This cannot be changed. | |||
* 01 - Allow filter selection in transmit. Initially set OFF. | |||
* 02 - Antenna tuner power down. Initially set to OFF. | |||
* 03 - Antenna tuner non-stop mode. When set to on, the antenna tuner will not stop when the lowest VSWR is found. Initially set to OFF. | |||
* 04 - Store mode, and filter settings prior to changing bands, or channels. Initially set to ON. | |||
* 05 - Display -HELLO- on digitial display, and send it in Morse code on power up. Initially set OFF. | |||
* 06 - Turn full LCD display ON on power on. Initially set OFF. | |||
=Naměřené hodnoty= | =Naměřené hodnoty= | ||
Latest revision as of 13:10, 9 November 2010
Nastavení pro optimální čistotu signálu
- CAR = max
- PROC = 7
- MIC = max
- PWR = max
- RF = max
- NB1 = on
- NB2 = off
- MONI = 1
- PROC = on
- MONI = on
- VOX = on
- Dávač = skoro max
Nastaveni pro buzeni LT2S+DB6NT
- CAR = max
- PROC = 7
- MIC = 6
Nastavení podle OK3RM
K rozumnému nastavení slouží měřidlo na TS850ce, kde si zapneš na měřáku PROC a nastavíš si max. 10dB kompresi. Pak si zapneš ALC a nastavíš si hladinu MIC maximálně na konec rozsahu ALC, když hodně moduluješ.
Propojení s LT2S
- Do IF OUT musí být přivedeno +12V pro zapnutí IF OUT a vypnutí PA.
- V REMOTE konektoru musí být propojeny piny +12 VDC on transmit (7) se Speaker output (1). Na kusu OK1MZM je na Speaker output zapojené zapnutí IF OUT.
TS-850s remote konektor - Přepínač LINEAR AMP na zadním panelu musí být zapnutý
Klíčování
Při klíčování mikrofonním konektorem
nelze mezi piny STBY (2) a GND (8) použít optočlen s Darlingtonem. Na něm je totiž velký úbytek cca 0.7 V a rádio zaklíčuje jen "napůl". Červená LED na předním panelu se rozsvítí, ale na Meteru se nepřepne zobrazení na SWR (dle nastavení) a modulace je silně zkreslená (velmi slabá, jen basy). Funguje klíčování obyčejným optočlenem typu 4N26.
ACC2
IF OUT
CAT
Blokový diagram
Pressing SCAN + TX-M.CH will set the radio into its extended function mode. These options can be scrolled via the M.CH/VFO CH. switch. The following are the extended functions:
- 00 - This is the ROM Ce`ecksum displayed as a 4-digit hexadecimal number. This cannot be changed.
- 01 - Allow filter selection in transmit. Initially set OFF.
- 02 - Antenna tuner power down. Initially set to OFF.
- 03 - Antenna tuner non-stop mode. When set to on, the antenna tuner will not stop when the lowest VSWR is found. Initially set to OFF.
- 04 - Store mode, and filter settings prior to changing bands, or channels. Initially set to ON.
- 05 - Display -HELLO- on digitial display, and send it in Morse code on power up. Initially set OFF.
- 06 - Turn full LCD display ON on power on. Initially set OFF.
Naměřené hodnoty
Kus OK1MZM
| CAR | PWR | výkon [W] | odstup šumu [dBc/Hz] |
| 6 | 0 | 3.3 | -114.17 |
| 7 | 0 | 10 | -119.33 |
| 10 | 1 | 25 | -131.2 |
| max | max | 87 | -132.4 |