Programming FTDI devices: Difference between revisions

From Tučňák Wiki
Jump to navigation Jump to search
Ok1zia (talk | contribs)
2,353 edits
Created page with ' This page describes how to programm the FT232R chip for use in: * Davac4 / USB2LPT + Dávač_3.0 or Dávač_3.3 * Rotar4 / [[...'
 
Ok1zia (talk | contribs)
2,353 edits
 
(7 intermediate revisions by the same user not shown)
Line 1: Line 1:
=Programming FT232R=


This page describes how to programm the FT232R chip for use in:
This page describes how to program the FT232R chip for use in:
* Davac4 / [[Převodník_USB_→_LPT_pro_Dávač_3.x|USB2LPT]] + [[Dávač_3.0]] or [[Dávač_3.3]]
* [[Davac4|Dávač 4]] / [[Převodník_USB_→_LPT_pro_Dávač_3.x|USB2LPT]] + [[Dávač_3.0]] or [[Dávač_3.3]]
* Rotar4 / [[Usb2ttl|USB2TTL]]
* [[Rotar47|Rotár 4]], [[Rotar5|Rotár 5]] / [[Usb2ttl|USB2TTL]]
* [[Usbio|USBIO]]
* [[Usbio|USBIO]]
* [[Hdkeyb|HDKEYB]]
* [[Hdkeyb|HDKEYB]]


You need [[File:MProg3.5.zip|MProg 3.5]] (obsoleted by FT_Prog but always work.
You need [[File:MProg3.5.zip|MProg 3.5]] (obsoleted by FT_Prog but always works).


Run MProg
Run MProg


[[Image:MProg.png|none|frame|MProg initial state]]
[[Image:MProg.png|none|frame|MProg initial state]]
Disconnect all possible USB devices (can contain FTDI chip also). Connect your device with FT232R. Press Ctrl+N to create new programming template. Press Ctrl+C to scan. MProg responds in bottom box:
Number Of Blank Devices = 0
Number Of Programmed Devices = 1
Change:
* Device Type to FT232R
* USB VID/PID to Own VID & PID
* Vendor ID to A600
* Product ID by table bellow
* Manufacturer to OK1ZIA
* Product Description by table bellow
{| border="1" cellpadding="3" cellspacing="0"
| align="center" style="background:#f0f0f0;"|'''Device'''
| align="center" style="background:#f0f0f0;"|'''Product ID'''
| align="center" style="background:#f0f0f0;"|'''Product description'''
|-
| Davac4
| E110
| Davac 4.x
|-
| Rotar4
| E112
| Antenna rotator 4.x
|-
| USBIO
| E113
| USB GPIOs
|-
| HDKEYB
| E114
| HD44780 + Keyboard
|}
Verify entered data, press Ctrl+V and save configuration to file. Pres Ctrl+P to programm.
In bottom box result appears:
Programmed Serial Number : FTVCZQUP
[[Image:MProgDone.png|none|frame|MProg device programmed]]
Replug the device. Run Control Panel and you'll see new device:
[[Image:MProgControlPanel.png|none|frame|Control panel with new device]]
=Repair wrong VID/PID=
If you do a mistake and programm wrong Vendor/Product IDs to FT232R, you can try this recover procedure:
* Get real VID/PID from MProg or from Device Manager (Properties, Details, Hardware ID)
* Read section 4 of [http://www.ftdichip.com/Support/Documents/AppNotes/AN_107_AdvancedDriverOptions_AN_000073.pdf]
* Modify D2XX/CDM drivers to match device VID/PID. Leave only one device item like:
[Manufacturer]
%Ftdi%=FtdiHw,NTamd64
[FtdiHw]
%USB\VID_A600&PID_E112.DeviceDesc%=FtdiBus.NT,USB\VID_A600&PID_E112
[FtdiHw.NTamd64]
%USB\VID_A600&PID_E112.DeviceDesc%=FtdiBus.NTamd64,USB\VID_A600&PID_E112
[ControlFlags]
ExcludeFromSelect=*
* Scan devices in MProg, it should find the device
* Set proper values of VID/PID and programm these
* Without replug, Uninstall drivers in Device Manager
* Replug revice, it should have new VID/PID
=Another way, works also on bricked chips=
http://www.weirdlab.fr/?p=638
$ sudo apt-get install make gcc libftdi-dev
$ wget http://rtr.ca/ft232r/ft232r_prog-1.24.tar.gz
$ tar -zxvf ft232r_prog-1.24.tar.gz
$ cd ft232r_prog-1.24
$ make
$ sudo ./ft232r_prog –old-pid 0x000 –new-pid 0x6001

Latest revision as of 07:40, 22 March 2018

Programming FT232R

This page describes how to program the FT232R chip for use in:

You need File:MProg3.5.zip (obsoleted by FT_Prog but always works).

Run MProg

MProg initial state

Disconnect all possible USB devices (can contain FTDI chip also). Connect your device with FT232R. Press Ctrl+N to create new programming template. Press Ctrl+C to scan. MProg responds in bottom box: 

Number Of Blank Devices = 0
Number Of Programmed Devices = 1

Change:

  • Device Type to FT232R
  • USB VID/PID to Own VID & PID
  • Vendor ID to A600
  • Product ID by table bellow
  • Manufacturer to OK1ZIA
  • Product Description by table bellow


Device Product ID Product description
Davac4 E110 Davac 4.x
Rotar4 E112 Antenna rotator 4.x
USBIO E113 USB GPIOs
HDKEYB E114 HD44780 + Keyboard


Verify entered data, press Ctrl+V and save configuration to file. Pres Ctrl+P to programm.

In bottom box result appears: 

Programmed Serial Number : FTVCZQUP
MProg device programmed

Replug the device. Run Control Panel and you'll see new device:

Control panel with new device

Repair wrong VID/PID

If you do a mistake and programm wrong Vendor/Product IDs to FT232R, you can try this recover procedure:

  • Get real VID/PID from MProg or from Device Manager (Properties, Details, Hardware ID)
  • Read section 4 of [1]
  • Modify D2XX/CDM drivers to match device VID/PID. Leave only one device item like:
[Manufacturer]
%Ftdi%=FtdiHw,NTamd64 

[FtdiHw]
%USB\VID_A600&PID_E112.DeviceDesc%=FtdiBus.NT,USB\VID_A600&PID_E112 

[FtdiHw.NTamd64]
%USB\VID_A600&PID_E112.DeviceDesc%=FtdiBus.NTamd64,USB\VID_A600&PID_E112

[ControlFlags]
ExcludeFromSelect=*
  • Scan devices in MProg, it should find the device
  • Set proper values of VID/PID and programm these
  • Without replug, Uninstall drivers in Device Manager
  • Replug revice, it should have new VID/PID

Another way, works also on bricked chips

http://www.weirdlab.fr/?p=638 

$ sudo apt-get install make gcc libftdi-dev
$ wget http://rtr.ca/ft232r/ft232r_prog-1.24.tar.gz
$ tar -zxvf ft232r_prog-1.24.tar.gz
$ cd ft232r_prog-1.24
$ make
$ sudo ./ft232r_prog –old-pid 0x000 –new-pid 0x6001
Retrieved from "https://tucnak.nagano.cz/wiki/index.php?title=Programming_FTDI_devices&oldid=2608"